Rose electronic Ultraview Pro KVM SWITCH WITH ON-SCREEN DISPLAY Manuel d'utilisateur

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 Internet: WWW.ROSE.

4 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL CPU connection All CPU connectors on the UltraView Pro are DB25F. The CPUs are connected to the

MODELS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 5 UltraView Pro models “M” chassis “B” chassis “C” chassis Figure 1. UltraView mode

6 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL UltraView Pro models (rear) “M” Chassis “B” Chassis “C” Chassis Figure 2. Rear Panel Label

CABLES ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 7 UltraView Pro Cables (See Appendix C for cable part numbers) UltraView Pro to KVM statio

INSTALLATION 8 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Organizing the system It is recommended that before any UltraView Pro configuration

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 9 The green POWER LED will turn on and the power-on diagnostic message will display on the KVM mon

10 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL (4 CPUs can be connected using a 4-port unit, 16 using a 16-port unit) Figure 3. UltraView Pro

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 11 * 4 units can be cascaded using a 4-port master/16 using a 16-port master Figure 4. Cascadin

12 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 8. Next, select “Expansion width” from the configure system menu and press enter. Enter the n

CONFIGURATION MENUS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 13 Main configuration menu Figure 5. Main configuration menu The UltraView

14 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Configure system menu Figure 6. Configure system menu By selecting “SYSTEM” fr

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 15 Expansion If your system consists of cascaded units, the expansion section of the Configure Sys

16 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL To change the scan time, highlight “Scan time” and press enter. An input box will display for

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 17 Delay This setting is for PC keyboards only. It is used to adjust how long, after a key is dep

18 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Configure computer menu Figure 7. Configure computer menu The “Configure

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 19 Keyboard To change a computers keyboard and/or mouse, use the up/down arrow keys to select (hig

20 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Configure overlay Figure 8. Configure overlay menu The “Configure overlay”

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 21 Resolution Use this configuration to set the resolution for the KVM stations video if no comput

22 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Configure overlay - Computer select window The “Computer select window” section allows you to c

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 23 Background color To change the background color, select “Background color” and press enter. A

LIMITED WARRANTY Copyright  Rose Electronics 1990-2002. All rights reserved. No part of this manual may be reproduced, stored in a retrieval system,

24 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL This item sets the font type for the computer label. To change the font, select “Font” and pre

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 25 Configuration password To assign a “Configuration password”, select it from the “Configure secu

OPERATION 26 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Selecting a computer To connect to a computer, you can select it from the UltraView P

KEYBOARD COMMANDS ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 27 Keyboard commands The following table describes the available keyboard comman

28 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Mode value Description M1 CPU keyboard = PC mode 1 (Some IBMs & PS/1’s) M2 CPU keyboa

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 29 Keyboard command usage When using keyboard commands to enter information to the UltraView Pro,

RS232 PORT 30 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Serial Port (RS232) The RS232 serial port on the UltraView Pro’s rear panel is used

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 31 To update the UltraView Pro’s firmware, first download the latest revision from Rose Electronic

32 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL If any of these errors occur, check the RS232 cable, the connectors, and the adapter. Make sure

TROUBLESHOOTING ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 33 TROUBLESHOOTING Computer does not boot, keyboard or mouse error received.  Cab

FCC/IC STATEMENTS, EU DECLARATION OF CONFORMITY FEDERAL COMMUNICATIONS COMMISSION AND INDUSTRY CANADA RADIO-FREQUENCY INTERFERENCE STATEMENTS This

34 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Mouse does not move  Mouse not configured.  UltraView Pro turned off after or not connect

SERVICE AND MAINTENANCE ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 35 Service Information Maintenance and Repair This Unit does not contain

SAFETY 36 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Safety This UltraView Pro KVM switch has been tested for conformance to safety regulati

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 37 Safety and EMC Regulatory Statements Safety Information Documentation reference symbol. If the

38 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Informations concernant la sécurité Symbole de référence à la documentation. Si le produit es

APPENDICES ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 39 Appendix A. Initial factory settings Setting Default value KVM keyboard/mouse type

40 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Appendix B. Parts and cables Part number Description CAB-CX0606Mnnn** Coax VGA-PS/2 Kbd-PS/

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 41 Appendix C. General Specifications The UltraView Pro part number is Uxy-zUB Where x = platform

42 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Appendix D. Rack mount instructions The UltraView Pro can be mounted in a rack using the Rackm

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 43 Appendix E. Rack mount illustration Appendix F. Keyboard mapping Sun / Apple keyboa

TABLE OF CONTENTS Contents Disclaimer ... 1 Introduction / System

44 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL Appendix G. Video distance capability The table below shows the distances, resolution, and q

10707 Stancliff Road Houston, Texas 77099 Phone: (281) 933-7673 WWW.ROSE.COM

Figures Figure 1. UltraView models ... 5 Figure 2. Rear Panel ...

INTRODUCTION ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 1 Disclaimer While every precaution has been taken in the preparation of this manual,

2 ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL All UltraView Pro models can easily be expanded by chaining the units together and configuring t

ULTRAVIEW PRO INSTALLATION AND OPERATIONS MANUAL 3 Compatibility Computers Industry standard PCs, Sun, Unix computers such as RS/6000, HP, SGI, DEC